...
- DDI – Numeric digits and "+" only. This should be the name in the DDI directory. This will become associated with the campaign on a longest prefix match basis. eg if DDIs "85" and "851" exist then campaigns declaring the following DDI string will get the following DDI associations:
"859027634" -> DDI "85"
"8510978344" - > DDI "851"
"8906467731" - DDI "default" - RejectMessage - is the name of an audio file to be played to a call before it is dropped. The file is located in the specific DDI directory. If not set the rejected call will be dropped with a BUSY cause, without being answered. Call centre managers should be aware of any premium rate or similar charges that will preclude the answering and rejection of a call in such a way. Answering higher charge rate calls to offer a rejection message may be illegal in some regions and costly in others.
- ComplusoryIntroMessage CompulsoryIntroMessage - is the name of an audio file to be played by the telephony platform on call arrival. The file is located in the specific DDI directory. The file is played entirely and uninterrupted before the call is eligible for queuing or distributing. If set, the call will be answered after 3 seconds to permit network signalling (audio and digital) to propagate. If the file is not present the call will begin to queue immediately.
- InitialQueueMessage - is the name of an audio file to be played by the telephony platform on when the call is initially queued. The file is located in the specific DDI directory. There will be a delay before the file is played. The file will be played 5 seconds after the call is queued. Unlike the ComplusoryIntroMessageCompulsoryIntroMessage, the message may be interrupted if the call can be transferred to an agent.
- QueueMessage - is the name of an audio file to be played repeatedly on the queue after the initial file, and until the call is distributed off the queue, or drops. The file is located in the specific DDI directory. between each play there will be a specified gap. This gap may have MessageOnHold or ringing
- MessageGap – the number of seconds between file play cycles. This parameter is specified in a Params.xml file in the specific DDI directory. The default value is 20
- MaxQueueTime - This is the maximum wait time in seconds permitted before the queue is frozen. This parameter is specified in a Params.xml file in the specific DDI directory. The maximum number of calls on the queue will be frozen from the time the limit was exceeded until the longest wait time of any call on the queue drops below the limit. Any call that arrives and cannot be queued due to this condition will be rejected; this prevents callers into the system being accepted but having to wait for long periods. This should be used when supervisors regard call rejection as preferable to long queuing. If no rejection condition is wanted, this number can be set very high. Rejected calls may be played a file before being rejected.
Here is an example of a Params.xml file. The default value is 0 (not applied)
<?xml version="1.0" encoding="utf-8"?>
<Parameters xmlns:xsd="http://www.w3.org/2001/XMLSchema" xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance"><MessageGap>20</MessageGap><MaxQueueTime>0</MaxQueueTime></Parameters>
Inbound calls history is available via DiallerConsole and WebConsole. They are marked as "Inbound". Any call that is dropped by the caller before it reaches an agent (eg, while queuing) will be marked as FASTDROP, similarly outbound calls that might be dropped (in the short time) between answer and drop.
...
Confirmit CATI declares its own DDIs into the dialler. When a call comes in the dialler notifies the Confirmit CATI and it will determine how the call should be handles. Call acceptance and Interviewer selection can be optionally performed by the CATI. To avoid using the diallers own call acceptance and Interviewer selection mechanisms, the DDI should not be predifined in the dialler's own set-up. Valid Confirmit DDI numbers shall be declared by confirmit only. See Confrmit documentation on setting this up. However, If a "default" DDI is set up, then the handling of a Call will use the default parameters unless overridden by confirmit.
Confirmt is able to override the ComplusoryIntroMessageCompulsoryIntroMessage.
Confirmt also supports an array of call rejection messages. These are specified in the CATI supervisor. Please refer to the Confirmit documentation in this respect.
Invades support for Confirmit inbound call handling also supports skill-set grouping. If the CATI requests interviewer allocation by the dialler, only interviewers with matching skill-set group allocations will be assigned to incoming calls
Confirmit inbound is support in versions 6.4 and above for the dialler and 6.0.0 of the ConfirmitDiallerProyx.